INTERNATIONAL ONE METRE CLASS 2007 BOAT MEASUREMENT FORM (this is not a certificate)

Authority: ISAF - RADIO SAILING DIVISION

IN ORDER TO OBTAIN A CERTIFICATE

1 The hull registration number shall be issued by the owner's certification authority.

2 An official measurer shall carry out certification control.

3 The measurement forms, when completed, together with any registration fee that may be required, shall be sent to the

owner's certification authority.

NB - Certification Authority When issuing a hull registration number, send the applicant one copy each of the boat measurement form and the rig/sail measurement form.

Retain all the measurement forms when issuing a certificate. Certificate has been issued to owner YES NO

BEFORE SENDING TO THE CERTIFICATION AUTHORITY

PLEASE MAKE SURE THAT THIS FORM IS PROPERLY COMPLETED

Hull Reg. Number .........................…..............................................................................

Boat's Name ...........................................................................................................

Owner's Name ...........................................................................................................

Owner's Address ...........................................................................................................

...........................................................................................................

Design’s Name ...........................................................................................................

Designer’s Name ...........................................................................................................

Builder(s) ...........................................................................................................

Date of Initial Certification Control / Fundamental Measurement ...............................

NB - MEASURERS

1 Measurements shall be carried out in accordance with the Equipment Rules of Sailing except where varied in the class rules.

2 If the official measurer has any doubt concerning the application of, or compliance of any part of the boat with, the class rules he shall report it on the measurement form(s) before sending them to the certification authority and not sign measurement form(s) or sails.

3 The boat shall comply with all the class rules in Sections D, E, F, G and H even if some of the rules are not mentioned on the measurement form(s).

HULL

1	D.1.4	Is the registration number marked in an easily visible location on a non-removable part of the hull, excluding fittings and corrector weights, by any of: painting, engraving, bonding, moulding?	yes / no
2	D.1.5	Is there a deck limit mark, of 5 mm min diameter, displayed on the centreplane of the hull near to the mast position?	yes / no
3	D.2.1(a)	Is the hull made of and joined using only the materials permitted by class rule D.2.1(a)?	yes / no
4	D.2.1(b)	Does the GRP conform to class rule D.2.1(b)?	NA / yes / no
5	D.2.1(c)	With the exception of elastomeric materials, are any materials expanded, foamed and/or honeycombed?	yes / no
6	D.2.1(c)(3)	If the hull contains Texalium was its initial fundamental measurement prior to 1 September 2004?	NA / yes / no
7	D.2.2(a)	Is the hull a monohull?	yes / no
8	D.2.2(b)	Except for trunking for the keel and rudder, does the hull have:
9		(1) voids in the waterplane and/or underwater profile?			yes / no
10		(2) hollows in the plan view and/or underwater profile that exceed 3 mm?			yes / no
11		(3) transverse hollows in the undersurface of the hull that exceed 3 mm when tested parallel to the waterplane as in figure H.2?			yes / no
12	D.2.2(c)	Is the forward 10 mm of the hull of elastomeric material?			yes / no
13	D.2.2(d)	Is the rudder attached to the hull aft of where the keel is attached?			yes / no
14	D.2.3(a)	Are fittings which contribute to the stiffness and/or strength and/or watertight integrity of the hull made only of materials permitted by D.2.1?			yes / no
15	D.2.3(b)	Are ball and/or roller bearings used for any items other than: sheet control line blocks, mainsail boom sheet blocks, headsail boom sheet blocks?			yes / no
16	D.2.3(c)	Do any fittings project outboard of the hull shell or deck?			yes / no
17	D.2.4	Does the remote control equipment conform to class rule D.2.4?			yes / no
APPENDAGES
18	E.1.1	Does the keel conform to class rule E.1.1?			NA / yes / no
19	E.3.2(a)	Are the keel and rudder removable from the hull?			yes / no
20	E.3.2(b)(1)	Are the keel and rudder connected?			yes / no
21	E.3.2(b)(2)	Are the keel and/or rudder articulated?			yes / no
22	E.3.2(b)(3)	Do the keel and/or rudder have openings through which water could flow when in use?			yes / no
23	E.4.1	Is the largest transverse dimension greater than 20 mm measured at any point 60 mm or more above the lowest point of the keel?			yes / no
RIGS
24	Measurement form/s for rigs and its sails attached			1	2	3

DECLARATION BY THE OWNER

Only materials listed in D.2.1 have been used in the construction of this hull, no materials with a density exceeding 11,300 kg/m³ have been used in the construction of the hull appendages. I also undertake to maintain this boat in compliance with the class rules and that alterations or repairs to equipment required by the measurement form to be measured will be checked by an official measurer before use.

Signature Date

................................................................. .................................................................

MEASURER’S COMMENTS

If the official measurer has any doubt concerning the application of, or compliance of any part of the boat with, the class rules he shall report it on the measurement form(s) before sending them to the certification authority and not sign measurement form(s) or sails.

DECLARATION BY THE MEASURER

I confirm that I have taken the measurements on this form, that the particulars on this form are correct and that, to the best of my knowledge, the boat complies with the rules covered by this form. I have stated above in MEASURER’S COMMENTS those points where I have any doubt concerning the application of, or compliance of any part of the boat with, the class rules whether or not they are covered by the measurement form.

Name of Measurer	Officially recognised by
(BLOCK CAPITALS)	(ISAF Member National Authority of Country)
...................................................................................................	..................................................................................................
Signature	Date
...................................................................................................	..................................................................................................