A.1.2 The word “shall” is mandatory and the word “may” is permissive.

A.5.1 These class rules shall be read in conjunction with the 2005-2008 ERS.

A.5.2 Except where used in headings, when a term is printed in “bold” the definition in the ERS applies and when a term is printed in “italics” the definition in the RRS applies.

A.9.1 GENERAL

Interpretation of class rules, except as provided by A.9.2, shall be made in accordance with the ISAF–RSD Regulations.

A.9.2 AT AN EVENT

Any interpretation of class rules required at an event may be made by an international jury constituted in accordance with the RRS. Such interpretation shall only be valid during the event and the organising authority shall, as soon as practical after the event, inform the ISAF–RSD, the DM and the ICA.

A.10.1 Registration numbers shall be issued by the certification authority.

A.10.2 Registration numbers shall be issued in consecutive order starting at “1”.

A.10.3 Each hull shall have a unique registration number which shall include the national letters and the certification authority’s sequential registration number. Under no circumstances may a registration number be used on a hull other than the hull on which it was first used.

A.12.1 A certificate becomes invalid upon:

(a)

a change of ownership,

(b)

withdrawal by the certification authority,

(c)

the issue of another certificate.

A.13.1 A boat ceases to comply with the class rules upon:

(a)

use of equipment that does not comply with limitations in the class rules,

(b)

use of equipment that does not comply, or that causes the boat not to comply, with limitations recorded on the certificate,

(c)

alteration or repair of equipment required by the measurement form(s) to be measured, except where permitted by the class rules,

(d)

a change of class rules that causes equipment in use to cease to be permitted, except where the equipment may comply with the class rules in force at the time of its initial certification control.

B.1.1 The hull shall have a valid certificate.

B.1.2 A certificate issued prior to the effective date of these class rules remains valid until any of the criteria in A.12.1 is met.

C.3.1 LIMITATIONS

The boat shall display only such advertising as permitted by the ISAF Advertising Code, Category C.

C.4.2 WEIGHT

minimum maximum The weight of boat in dry condition excluding wind indicator if used ............................................................ 4000 g

C.4.3 CORRECTOR WEIGHT(S)

Corrector weight(s) to achieve compliance with C.4.2, if used, shall be fixed in/on the hull.

C.4.4 WATER

Water shall not be used to trim the boat and it may be removed at any time.

C.5.1 IDENTIFICATION

The hull registration number shall be displayed on the external surface of the hull shell or deck clearly and legibly with a minimum height of 20 mm.

C.5.2 MAINTENANCE

Routine maintenance to the hull such as removing and adding fittings and remote control equipment, replacing hull patches, painting, polishing, smoothing etc., is permitted without re-measurement and re-certification provided the compliance with D.2 is not affected.

C.5.3 REMOTE CONTROL EQUIPMENT

USE

(a)

The rudder control unit shall control the rudder only.

(b)

The sheet control unit shall control the mainsail sheet and headsail sheet only.

(c)

Except for control unit positioning and radio link information, no radio transmissions from the boat shall be made.

(d)

Remote control and/or related equipment if temporarily removed and or replaced:

(1)

shall be refitted in the same position.

(2)

shall be replaced by equipment of similar weight.

C.6.1 MAINTENANCE

The hull appendages may be altered after certification control, without undergoing new certification control, provided compliance with E.3 is not affected.

C.6.2 LIMITATIONS

Except when a hull appendage has been lost or damaged beyond repair, only one keel and one rudder shall be used during an event. Replacement may be made only with the approval of the race committee. Unless the hull appendage has been lost, the race committee shall remove or cancel any Event Limitation Mark attached to the hull appendage that has been replaced.

C.6.3 USE

(a)

The keel shall not move or rotate relative to the hull, except by flexing.

(b)

The hull appendages shall not project outboard of the hull.

C.6.4 WEIGHTS minimum maximum

Keel, excluding fasteners to hull ........................................ 2200 g ....... 2500 g Rudder, including stock ................................................................. ............ 75 g

C.7.1 LIMITATIONS

Except when an item has been lost or damaged beyond repair, one mast, one mainsail boom and one headsail boom, for each of the three rigs, may be used during an event. Replacement may be made only with the approval of the race committee. Unless the spar is lost, the race committee shall remove or cancel any Event Limitation Mark attached to the spar that has been replaced.

C.7.2 USE

The rig shall not project beyond the fore and aft ends of the hull.

C.7.3 ADDED WEIGHTS

(a)

Weights of any material may be positioned in and/or on a mast spar below the lower point. Weights of density greater than 8.000 kg/m³ may be positioned in and/or on a mast spar above the lower point.

(b)

Such weights may be removed or added at any time subject to C.4.1 and

C.4.2.

C.7.4 MAST

(a)

DIMENSIONS minimum maximum Lower point to deck limit mark as defined in D.1.5 ................................................ 60 mm .... 100 mm Within these limits, the variation in height of lower point for each rig ................................................... ...... ± 5 mm

Mast spar curvature between lower point and upper point ...................................................................... unrestricted

(b)

USE The spar stepping position and wind indicator position are optional.

C.7.5 BOOMS

DIMENSIONS minimum maximum Boom spar curvature measured between points on the top of the spar 10 mm from each end ................................ ......... 3 mm

C.7.6 STANDING RIGGING

USE

The headsail boom swivel shall be attached to the hull approximately on the hull centreplane. The alignment of the swivel between the hull and the headsail boom shall be controlled only by the rigging tension.

C.7.7 RUNNING RIGGING

USE

(a)

The mainsail sheet and the headsail sheet may be worked by a sheet control line attached to the sheet control unit.

(b)

The upper end of any headsail boom topping lift shall be attached to the headsail halyard and/or stay, or their mast spar fitting(s).

(c)

A headsail boom topping lift restraint line attached to, or passing around, the topping lift may be attached to and/or passed around any or all of the following: topping lift; headsail; headsail halyard; headsail stay; headsail boom.

(d)

A mainsail tack control line may be passed around or through the mast spar, the mainsail boom spar and/or their fittings.

C.8.1 MAINTENANCE

Routine maintenance such as replacement of battens and patching over damaged areas is permitted without re-measurement and re-certification.

C.8.2 LIMITATIONS

Except when a sail has been lost or damaged beyond repair, no more than one mainsail and one headsail, for each rig, shall be used during an event. Replacement may be made only with the approval of the race committee. Unless the sail is lost, the race committee shall remove or cancel any Event Limitation Mark attached to the sail that has been replaced.

C.8.3 IDENTIFICATION

Identification shall comply with the RRS. Sails certified before 1^st January 2005 shall comply with the sail identification rules in force at that time or at the time of initial certification.

C.8.4 USE

(a)

GENERAL

(1)

A sail of one rig shall not be used with another rig.

(2)

A sail may not be used alone, except where the other sail of that rig has been lost or damaged during the race.

(b)

MAINSAIL

(1)

The tack point shall not be set more than 25 mm forward of the forward end of the boom spar and the clew point shall not be set more than 25 mm aft of the aft end of the boom spar.

(2)

Any luff bolt rope or luff slides shall be set in a mast spar track.

(3)

Luff tabling may envelop a mast spar jackstay.

(c)

HEADSAIL

(1)

A line taken through the tack point and the head point shall cut the forward face of the mast spar lower than the lower edge of the headsail stay limit mark at the fore side of the spar when the boom spar is on the centreplane of the hull.

(2)

The tack point shall not be set more than 25 mm forward of the forward end of the boom spar and the clew point shall not be set more than 25 mm aft of the aft end of the boom spar.

(3)

Luff tabling may envelop the headsail stay.

(4)

Any luff slides shall be set on the headsail stay.

D.1.1 RULES

The hull shall either comply with the class rules in force at the time of its initial certification control or comply with the current class rules.

D.1.2 CERTIFICATION

See rule A.11.

D.1.3 BUILDERS

(a)

No building licence is required for hulls built in accordance with D.2.1.

(b)

A building licence may be granted to commercial builders who wish to use mass production methods to lower the cost of hulls, but which do not comply with D.2.1. Such licence shall be based on a building specification approved by the ICA and the ISAF–RSD and a contract between the ISAF–RSD and the builder.

D.1.4 IDENTIFICATION

The hull registration number shall be marked in an easily visible location on a non-removable part of the hull excluding fittings and corrector weights by any of the following means: painting on, engraving in, bonding in, moulding in.

D.1.5 DECK LIMIT MARK

The deck limit mark shall be displayed on the centreplane of the hull near to the mast position. It shall be a minimum of 5 mm in diameter.

D.2.1 MATERIALS

(a)

Subject to (b) and (c), the hull, excluding fittings and remote control equipment but including any supports and containers for such items, shall be made of and joined using one or more of the following materials:

(1)

metal,

(2)

wood; wood based products containing only permitted materials,

(3)

glass fibre reinforced plastic,

(4)

adhesive,

(5)

varnish; paint,

(6)

film covering materials which may be fibre reinforced,

(7)

elastomeric material,

(8)

thermoplastic, which may be moulded, containing only permitted materials.

(b)

In glass fibre reinforced plastic:

(1)

an external gel coat is optional and may be pigmented,

(2)

an external paint coating is optional,

(3)

the laminating resin shall be unpigmented,

(4)

the reinforcement shall be glass fibre in any of the following forms: roving, tape, chopped strand mat and woven cloth,

(5)

the interior shall be un-coated to permit non-destructive examination for verification of the material content.

(c)

With the exception of elastomeric materials, materials shall not be: expanded, foamed, honeycombed.

(d)

Unrestricted by (a) and (b):

(1)

a builder’s mark may be applied,

(2)

the hull registration number shall be applied.

(3)

A hull made with Texalium and with a date of initial fundamental measurement, prior to 1 September 2004 may be certified.

D.2.2 CONSTRUCTION Construction is unrestricted subject to the following:

(a)

The hull shall be a monohull.

(b)

Except for trunking for the keel and rudder, the hull shall not have:

(1)

voids in the waterplane and/or the underwater profile,

(2)

hollows in the plan view and/or the underwater profile that exceed 3 mm,

(3)

transverse hollows in the undersurface of the hull that exceed 3 mm when tested parallel to the waterplane as in figure H.2.

(c)

The forward 10 mm of the hull shall be of elastomeric material.

(d)

The rudder shall be attached to the hull aft of where the keel is attached.

D.2.3 FITTINGS Fittings are unrestricted except that:

(a)

Fittings that can contribute to the stiffness and/or strength and/or watertight integrity of the hull shall be of materials permitted by D.2.1.

(b)

Ball and/or roller bearings may be used for: sheet control line blocks, mainsail boom sheet blocks, headsail boom sheet blocks.

(c)

Fittings shall not project outboard of the hull shell or deck.

D.2.4 REMOTE CONTROL EQUIPMENT

(a)

The following is permitted:

(1)

One receiver.

(2)

One rudder control unit.

(3)

One sheet control unit.

(4)

Battery cells assembled in one or more packs.

(5)

Electric cables, connectors and switches.

(b)

The rudder control unit and the sheet control unit may contain ball and/or roller bearings.

(c)

Remote control equipment may be fastened using hook and loop fasteners and/or the materials listed in D.2.1(a).

E.1.1 MANDATORY

(a)

Keel, which may comprise a fin and a bulb.

(b)

Rudder

E.2 GENERAL

E.2.1 RULES Hull appendages shall comply with the current class rules.

E.2.2 BUILDERS No licence is required.

F.1.1 MANDATORY

(a)

Mast.

(b)

Mainsail boom.

(c)

Headsail boom.

(d)

Standing rigging.

(e)

Running rigging.

(f)

Fittings.

F.2.1 RULES

Rigs shall comply with the current class rules.

F.2.2 MANUFACTURERS

No licence is required.

F.2.3 LIMITATIONS

The function of items shall be limited to what is normally provided by items of their type.

F.2.4 CONSTRUCTION

(a)

Fittings and/or control lines may be combined provided their function is not extended beyond what is permitted.

(b)

The position of parts, and the length and tension of rigging, may be adjustable unless otherwise restricted.

(c)

Ball and/or roller bearings may be used for: kicking strap fitting; gooseneck; mainsail boom sheet blocks; headsail boom sheet blocks; headsail boom swivel.

F.3.1 MATERIALS

(a)

The spar shall be aluminium alloy of 2024, 6005, 6061, 6063, 6082 or 7075 grade, or wood.

(b)

Other permitted materials in the spar are: adhesive; paint; powder coat; varnish; wax. An aluminium alloy spar may be anodised.

F.3.2 CONSTRUCTION

(a)

A mast stub arrangement is permitted and, if used, shall be taken to be part of the mast.

(b)

Between the lower point and the upper point the spar section shall be:

(1)

of circular outer shape,

(2)

constant within the variations permitted by F.3.4 except for the following permitted

items:

an internal sail track,

local cutaways for the insertion of a bolt rope or slides, openings for

fittings and/or rigging, internal and/or external spar joiners.

(c) Limit marks may be applied by the following means:

(1)

paint,

(2)

self adhesive tape,

(3)

fittings.

F.3.3 FITTINGS

(a)

MANDATORY

(1)

Mainsail halyard fitting or opening.

(2)

Shroud fitting(s) or opening(s).

(3)

Gooseneck.

(4)

Kicking strap fitting.

(b)

OPTIONAL

(1)

Wind indicator and/or its fitting.

(2)

Backstay crane and its fitting.

(3)

Headsail stay fitting or opening.

(4)

Headsail halyard fitting or opening.

(5)

Pair of spreaders and their fittings(s) and/or opening(s).

(6)

Mast spar rings and/or loops to attach mainsail luff to the spar.

(7)

Mainsail jackstay fittings.

(8)

Mainsail tack fitting(s).

(9)

Mast strut and its fitting.

(10)

Checkstay fittings(s).

(11)

Deck fitting.

(12)

Heel fitting with or without mast jack.

(13)

Added weights.

(c)

CONSTRUCTION

(1)

A mainsail halyard fitting may include one part that rotates with the sail about an axis located inside or outside the spar section.

(2)

The mainsail boom spar and the kicking strap pivot points shall be aft of the mast spar in the regions adjacent to these points.

F.3.4 DIMENSIONS minimum maximum Lower point to upper point mast 1 ....................................................................................... ... 1600 mm mast 2 ....................................................................................... ... 1180 mm mast 3 ....................................................................................... ..... 880 mm Lower edge of headsail stay limit mark at fore side of spar to upper point mast 1 ......................................................................... 220 mm mast 2 ......................................................................... 160 mm mast 3 ......................................................................... 120 mm Height of checkstay rigging point above heel point ..................... ..... 100 mm Spar between lower point and upper point ignoring features permitted by F.3.2(b): diameter...................................................................... 10.6 mm difference between largest and smallest diameter .................... ...... 0.3 mm

for an aluminium spar, the difference between

largest and smallest value along the spar of

any wall thickness dimension ............................................ ...... 0.1 mm

Length of spar joiners ..................................................................... ..... 100 mm Total length of local cutaways between lower point and upper point ....................................................................... ..... 100 mm Limit mark width ................................................................ 3 mm ...... 10 mm

F.4.1 MATERIALS

(a)

Spars shall be aluminium alloy of 2024, 6005, 6061, 6063, 6082, 7075, 7068 or 7178 grade, or wood.

(b)

Other permitted materials in the spar are: adhesive, varnish, paint, wax, powder coat. An aluminium alloy spar may be anodised.

F.4.2 CONSTRUCTION

The spar section shall be constant within the variations permitted by F.4.5 except for

(a)

the last 10 mm at each end,

(b)

openings for fittings and rigging.

F.4.3 MAINSAIL BOOM FITTINGS

(a)

MANDATORY

(1)

Mainsail clew fitting(s).

(2)

Mainsail boom sheet fitting(s).

(3)

Kicking strap fitting.

(b)

OPTIONAL

(1)

Mainsail tack fitting(s).

(2)

Gooseneck fitting.

F.4.4 HEADSAIL BOOM FITTINGS

(a)

MANDATORY

(1)

Headsail tack and clew fittings.

(2)

Headsail boom sheet fitting(s).

(3)

Swivel and/or its fitting(s).

(b)

OPTIONAL

(1)

Headsail stay fitting(s) or opening.

(2)

Topping lift fitting(s) or opening.

(3)

Counterweight and its attachment.

F.4.5 DIMENSIONS minimum maximum Spar, ignoring features permitted by F.4.2: largest external dimension ........................................................ ....... 20 mm

difference between the smallest and largest

value along the spar of any external

dimension ........................................................................... ...... 0.5 mm

for an aluminium spar, the difference between the largest and smallest value along the spar of any wall thickness dimension ............................... ...... 0.1 mm

F.5.1 MATERIALS

Except for terminations and the headsail boom swivel, the standing rigging shall be of steel and/or polymer.

F.5.2 CONSTRUCTION

(a)

MANDATORY

(1)

Pair of shrouds.

(2)

Backstay.

(3)

Headsail boom swivel.

(b)

OPTIONAL

(1)

Pair of checkstays if a mast strut is not fitted.

(2)

A headsail stay less than 1 mm in diameter.

(3)

A mast spar jackstay less than 1 mm in diameter.

F.5.3 FITTINGS OPTIONAL

(a)

Terminations.

(b)

Length and tension adjustments.

F.6.2 CONSTRUCTION

(a)

MANDATORY

(1)

Mainsail boom sheet.

(2)

Mainsail boom kicking strap.

(3)

Headsail halyard, if headsail stay is not fitted.

(4)

Headsail boom sheet.

(b)

OPTIONAL

(1)

Mainsail halyard.

(2)

Mainsail clew control line.

(3)

Mainsail tack control line

(4)

Headsail halyard.

(5)

Headsail clew control line.

(6)

Headsail tack control line.

(7)

Headsail boom topping lift.

(8)

Headsail boom topping lift restraint line.

F.6.3 FITTINGS OPTIONAL

(a)

Terminations.

(b)

Length and tension adjustments.

(c)

Mainsail boom sheet blocks, headsail boom sheet blocks.

G.1.1 MANDATORY

(a)

Mainsail.

(b)

Headsail.

G.2.1 RULES

Sails shall comply with the class rules in force at the time of their initial certification control.

G.2.2 CERTIFICATION

(a)

The official measurer shall certify sails in the tack and shall date each with the date of certification control.

(b)

An MNA may appoint one or more persons at a sailmaker to measure and certify sails produced by that manufacturer. A special licence shall be awarded for that purpose.

G.2.3 SAILMAKERS

No licence is required.

G.2.4 DEFINITIONS

Batten Pocket Point

The batten pocket point is defined as the intersection of the extended centreline of the batten pocket, or batten if there is no batten pocket, and the leech.

G.2.5 MEASUREMENT

(a)

During measurement:

(1)

battens need not be removed,

(2)

mainsails with the luff not set in a mast spar track may be attached to spars,

(3)

a headsail stay and mainsail mast spar jackstay need not be removed.

(b)

Where a mainsail has a luff bolt rope the luff shall be taken as the aft edge of the bolt rope.

(c)

Luff slides shall be ignored when measuring sail dimensions provided that their total length, measured along the luff, does not exceed 10% of the luff length.

G.3.1 CONSTRUCTION

(a)

MANDATORY

(1)

The construction shall be: soft sail, single ply sail.

(2)

The body of the sail shall consist of the same ply throughout and of not more than four parts joined by seams.

(3)

Seams shall not deviate more than 10 mm from a straight line between luff and leech.

(4)

The sail shall have three batten pockets, or battens if there are no batten pockets, at the leech.

(5)

The leech shall not extend aft of straight lines between:

(i)

the aft head point and the nearest batten pocket point,

(ii)

adjacent batten pocket points,

(iii) the clew point and the nearest batten pocket point. where the batten pocket points are to be taken as defined in G.2.4.

(6)

The foot shall not extend below a straight line between tack point and clew point.

(7)

Class insignia.

(b)

OPTIONAL

(1)

Tabling at the luff may form a pocket for a mast spar jackstay.

(2)

One or two cringles and/or openings at the head.

(3)

One cringle and/or openings at each of the clew and tack.

(4)

Luff openings for mast spar rings and/or loops for mast spar jackstay fittings.

(5)

Luff bolt rope.

(6)

Luff track slides.

(7)

Luff fittings for mast spar rings and/or loops.

(8)

Luff fittings for mast spar jackstay.

(9)

Primary reinforcement specified at G.3.3.

(10)

Secondary reinforcement specified at G.3.3.

(11)

Tell tales.

(12)

Not more than three sail shape indicator stripes, applied using paint or ink.

(13)

Sailmaker labels.

G.3.2 CONSTRUCTION TECHNIQUES

(a)

Only the following construction techniques shall be used where parts are joined or added as permitted in G.3.1 and G.3.3: welding; gluing; bonding with self adhesive tapes/materials; stitching.

(b)

Except for stitching, the joining techniques used at seams shall not extend beyond the edges of the seam.

G.3.3 DIMENSIONS minimum maximum Leech length: mainsail 1 ................................................................. 1610 mm .. 1620 mm mainsail 2 ................................................................. 1200 mm .. 1210 mm mainsail 3 ................................................................... 910 mm .... 920 mm Foot length: mainsail 1 ................................................................... 350 mm .... 360 mm mainsail 2 ................................................................... 340 mm .... 350 mm mainsail 3 ................................................................... 310 mm .... 320 mm Quarter width:

mainsail 1 ................................................................... 305 mm .... 315 mm mainsail 2 ................................................................... 295 mm .... 305 mm

mainsail 3 ................................................................... 265 mm .... 275 mm Half width: mainsail 1 ................................................................... 235 mm .... 245 mm mainsail 2 ................................................................... 225 mm .... 235 mm mainsail 3 ................................................................... 205 mm .... 215 mm Three-quarter width: mainsail 1 ................................................................... 135 mm .... 145 mm mainsail 2 ................................................................... 130 mm .... 140 mm mainsail 3 ................................................................... 115 mm .... 125 mm Top width ....................................................................................... ....... 20 mm Primary reinforcement: from nearest sail corner measurement point ......................... ..... 125 mm Secondary reinforcement: from nearest sail corner measurement point ......................... ..... 125 mm for flutter patches ................................................................... ....... 50 mm at luff fittings, luff slides and/or luff openings ........................ ....... 20 mm Tabling width ................................................................................. ....... 15 mm Seam width ..................................................................................... ....... 15 mm Seam to nearest sail corner measurement point ............ 150 mm Batten length: middle and lower ...................................................................... ..... 100 mm upper ......................................................................................... ....... 75 mm Batten width .................................................................................... ....... 10 mm Batten pocket length outside: middle and lower ...................................................................... ..... 120 mm upper ......................................................................................... ....... 95 mm Batten pocket width outside .......................................................... ....... 25 mm Batten pocket point, as defined in G.2.4, to nearest leech point ............................................................................... ....... 20 mm Largest cringle dimension ............................................................... ....... 10 mm With the exception for luff slides, largest luff fitting dimension ................................................................................. ....... 10 mm Sail shape indicator stripe width ..................................................... ....... 30 mm

G.4.1 CONSTRUCTION

(a) MANDATORY

(1) The construction shall be: soft sail, single ply sail.

(2) The body of the sail shall consist of the same ply throughout and of not more than three parts joined by seams.

(3) Seams shall not deviate more than 10 mm from a straight line between luff and leech.

(4)

The leech shall not extend aft of a straight line between the aft head point and the clew point.

(5)

The foot shall not extend below a straight line between tack point and clew point.

(b) OPTIONAL

(1)

Tabling at the luff may form a pocket for a headsail stay

(2)

One or two cringles and/or openings at the head.

(3)

One cringle and/or openings at each of the clew and tack.

(4)

Headsail stay slides and/or loops.

(5)

Primary reinforcement specified at G.4.3.

(6)

Secondary reinforcement specified at G.4.3.

(7)

Not more than two batten pockets, or battens if there are no batten pockets, at the leech.

(8)

Tell tales.

(9)

Not more than two sail shape indicator stripes, applied using paint or ink.

(10)

Sailmaker labels.

G.4.2 CONSTRUCTION TECHNIQUES

(a)

Only the following construction techniques shall be used where parts are joined or added as permitted in G.4.1 and G.4.3: welding; gluing; bonding with self adhesive tapes/materials; stitching.

(b)

Except for stitching, the joining techniques used at seams shall not extent beyond the edges of the seam.

G.4.3 DIMENSIONS minimum maximum Luff length: headsail 1 .................................................................. 1320 mm .. 1330 mm headsail 2 .................................................................... 980 mm .... 990 mm headsail 3 .................................................................... 730 mm .... 740 mm Leech length: headsail 1 .................................................................. 1245 mm .. 1255 mm headsail 2 .................................................................... 900 mm .... 910 mm headsail 3 .................................................................... 655 mm .... 665 mm Foot length: headsail 1 .................................................................... 375 mm .... 385 mm headsail 2 .................................................................... 340 mm .... 350 mm headsail 3 .................................................................... 290 mm .... 300 mm Half width: headsail 1 .................................................................... 185 mm .... 195 mm headsail 2 .................................................................... 165 mm .... 175 mm headsail 3 .................................................................... 140 mm .... 150 mm

Top width ....................................................................................... ....... 20 mm Primary reinforcement:

from nearest sail corner measurement point ......................... ..... 125 mm

Secondary reinforcement from nearest sail corner measurement point ......................... ..... 125 mm for flutter patches ................................................................... ....... 50 mm at headsail stay slides and/or loops .......................................... ....... 20 mm

Tabling width ................................................................................. ....... 15 mm Seam width ..................................................................................... ....... 15 mm Seam to nearest sail corner measurement point ............ 100 mm Batten length ................................................................................... ....... 75 mm Batten width .................................................................................... ....... 10 mm Batten pocket length outside ......................................................... ....... 95 mm Batten pocket width outside .......................................................... ....... 25 mm Clew point to lower batten pocket point as defined in G.2.4:

headsail 1 .................................................................... 400 mm .... 430 mm headsail 2 .................................................................... 285 mm .... 315 mm headsail 3 .................................................................... 205 mm .... 235 mm

Clew point to upper batten pocket point as defined in G.2.4: headsail 1 .................................................................... 820 mm .... 850 mm headsail 2 .................................................................... 590 mm .... 620 mm headsail 3 .................................................................... 425 mm .... 455 mm

Largest cringle dimension ............................................................... ....... 10 mm Sail shape indicator stripe width ..................................................... ....... 30 mm